Cellophane wrapping machine setup and maintenance
How to install the cellophane wrapping machinee, and don't make mistakes in the installation steps for setup, to make sure heat shrinkable film packaging machine can bring great convenience to our production and life, so the cellophane wrapping machine setup and maintainance is important!Cellophane wrapping machine setup: The correct installation steps of the heat shrink film packaging machine are as follows:
1. Since the heat shrink cellophane wrapping machine and the winding machine consume different powers, the input power must be higher than the nominal power on the nameplate of the heat shrink machine. Otherwise, the wiring and electricity will easily burn. components. When connecting to power, the customer must be careful not to cause any harm.
2. Like the baler, for personal safety, the wrapping machine must be reliably grounded. Prevent the generation of static electricity.
3. The power cord has been connected to each device before leaving the factory. The terminal leads have power identification symbols and must be connected correctly, otherwise improper operation may result in electric shock.
4. If the specified voltage of the machine is a three-phase 380V power supply, the neutral line must also be input at the same time. So another standard three phase four wire system is like a vacuum packaging machine. Otherwise, the machine will not work properly and the internal electronic components will easily burn.
5. If the machine is not installed horizontally, the life of the heating tube will be shortened. For mesh belt conveyors, diagonal installation will cause the belt to be off-center.
6. When the cellophane wrapping machine is used continuously for more than 3 months, it is necessary to check the heat-resistant wire in the shrink chamber and replace it appropriately according to the aging condition.
7. When the automatic cellophane wrapping machine is running, the operator's palms and other parts cannot come into contact with the operating parts of the machine. In particular, the temperature inside the shrink chamber is very high and easy to burn.
8. After completing the packaging work, please turn off the heating switch first, operate the transmission motor and fan motor for about 10 minutes, and then turn off the entire power supply.
Cellophane wrapping machine maintenance methods and precautions:
Maintenance methods of cellophane wrapping machine:
1. The blades should be cleaned and maintained with wire brushes and release agents. As for the moving parts, be sure to add lubricant regularly to ensure the normal operation of each component.
2. The blade contact surface is an important part of the sealing and wrapping machine, that is, the silicone strip must be well protected. If the outer layer of high-temperature varnish is found to be burned, the parts should be replaced immediately.
3. To replace the sealing and cutting blade, loosen the fixed chuck that holds the sealing and cutting knife, take out the sealing and cutting knife, clean the knife groove, install a new blade, place it in the groove and press it tightly, and fix both ends of the blade in the blade fixing clip. Inside the head, compress the spring and fix the screw.
4. If the cellophane wrapping machine cannot seal and cut the film or the sealing and cutting effect is not good, it may be caused by the following reasons:
① There is no voltage at both ends of the sealing and cutting blade (the sealing and cutting transformer is damaged or the connecting line is open, reconnect or replace it)
②The power supply voltage is too low (configure the input power supply for voltage stabilization)
③The sealing and cutting time is improperly adjusted or the time relay is damaged (readjust or replace)
④The cutting surface of the blade is uneven (it may be that the blade groove is not cleaned enough, so reinstall the blade)
⑤The blade is broken or has poor contact (the blade needs to be adjusted or replaced)
Cellophane wrapping machine maintenance precautions:
1. In order to ensure that the cellophane wrapping machine can maintain a complete sealing state for a long time, please clean the seal carefully after the sealing and cutting work steps are completed. Add lubricating oil to the mechanical oil filling port before operation to keep the machine lubricated. It is clean and does not produce noise, so that the paper cutter is always in good working condition.
2. For safety reasons, please clean the sealing knife before the temperature drops. After cleaning the cutter, dip a soft cloth into some cleaning paste and apply it gently on the seal. If the sealing knife cannot be completely sealed due to wear, the sealing knife needs to be replaced. ;
3. Air pressure relationship: To discharge waste water, the accumulated water must be discharged before reaching the metal baffle. After the piston at the bottom of the bottle is turned open, the water will be discharged. If it is squeezed from below, the piston may not be able to return to its original position. In case the piston cannot be When returning, please remove the bottom of the bottle and press the piston from top to bottom;
4. Pressure adjustment: When the adjusting button is rotated to the right, the secondary pressure will increase. After the pressure is set, please fix the fixed lock above the adjusting button;
5. Disassembly: Stop the flow of air injected into the regulator. Disassemble the four Panasonic screws, protective cover, spring, diaphragm assembly, plastic flat plate, baffle and other parts. Turn the bolt to the left and take it out. Remove the springs, piston gaskets, etc. after loosening them.
Thank you for support!
drip coffee bag packing machine manufacturer, pyramid tea bag packing machine, cellophane wrapping machine factory for tea box, coffee case, perfume carton, multi lane stick packing machine exporter, etc.
